|
|
|
|
|
|
|
|
|
|
http://www.wphidled.com/
Sales Manager : Amy Feng
MSN : Amy@wplamps.com Email : Amy@wplamps.com
Alibaba: cn220020193 Phone: 0086-13126403867
HID Installation FAQ
1.HID lamp safety performance?
A: Because our products AIDS has a strict anti-interference circuit and various electrical anomalies automatic protection function, so the products have any abnormal state in matching electronic ballast will automatically cut off the circuit. Cars and people will not have any risk, you can rest assured that use.
2.HID lights installed for those models?
A: Since we launched fit H1, H3, H4, H7, 9005,9006,9007 etc xenon lamp. So almost all of the models can be applied.
3.HID easy to install it?
A: Actually HID installation, is the original car's halogen bulb headlights off and put on the same model of xenon lamp light bulbs and to install the ballast, while the dust cover on the hole leads to harness, and to install relay line group, the installation is very convenient, but for the sake of safety recommendations by professional automotive electrician.
4. Q HID bulb waterproof it?
A: Our HID bulbs and electronic ballasts have been soaked in water experiments, so the HID lamp and ballast are waterproof, customers can rest assured that use.
5. Q. There are many models headlight rear cover is closed, what should lead to wiring harness?
A: If the cover is sealed 25MM reamer can punch in the back cover, back cover and then fit the waterproof seal cap.
6. Question the need to replace the fuse to install HID?
A: Because the HID bulb in the light of the moment will produce 2,3 million volts and high current, the original car's fuse normally 10A, proposed to 15-20A fuse, but after the installation does not require replacement of the relay line group fuse.
7. Q HID ballast 12V input correct. Reverse the negative ballast will burn?
A: No, if the power supply positive and negative reversed, the ballast protection circuit will automatically disconnect the power, the ballast will not burn, but not for a long time power.
8. Q HID lights installation, if all models have extracted before the big shade?
A: No, if there is sufficient space for the installation, you can not extract the headlights off.
9. Ballast asked how to identify good or bad? . .
A: First, by international standards, 20% light 1 second, 4 seconds to reach 80% brightness is a good stabilizer, and an instant 80% brightness or 4 seconds to reach the standard brightness of the ballast is poor quality. Second, the startup mode, start ballast is divided into two, one cold start, is the ballast and the bulbs are in a cooling state, turn on the lights; second hot start, is the ballast and the bulbs are in the normal operating temperature, type open light, do in this state continuously repeated switching, good quality ballast lights properly, there will be some lighting ballast is not normal, there will be a light bulb does not light a phenomenon. Shall cut off the power on again. The latter is obviously poor quality. Third, the current market is divided into two kinds of ballast, split and integrated; split is not convenient in terms of installation, while technically belong to the early products.
10. Bulbs currently on the market have 4300K, 5000K, 6000K, 8000K, 10000K 12000K even choose which is better? A: People have a misconception generally, the higher color temperature, brightness higher. In fact, the unit is lumens brightness (M), 4300K is white with a little yellow; 5000K close to natural light; 6000K white point blue slightly; 8000K is bluish; 10000K is blue; 12000K is blue has been presented. As we know, higher the temperature, the lower the lumens of light, its fog, rain penetration worse. The best general use 4300K ~ 6000K.
11. Q. There are many cars on the market today are using the H4 bulb, many people reflected the distance light HID lights are not used, is it?
A: Yes, because the H4 HID lights near and far are the following problems: First, the distance light is retractable, generally used motor, hydraulic, pneumatic and magnetic-action, and this time HID telescopic very easy to be stuck a few months he became a single lamp. Second, the telescopic HID lampholders are long, destructive of the original group, the larger lights, the installation is also more difficult, but also the phenomenon of water appears light. Third, the telescopic original HID lamps may need to destroy the original mask, which can lead to rotation as the current item. Four, two more lamp HID's rotation makes the car has increased considerably. As we all know, is based on the original halogen lamp design, the distance light-emitting halogen tungsten very close distance, while the two on the market today can not do that HID lamps. Beam makes this light simply can not meet demand with light fixtures, only the rotation out of the light, causing fatal injuries to other vehicles, but also affect its own security. In addition, the structure of this type of bulb it is easy to determine leakage, ignition, the light will ballast burned, heavy on the people, cars serious security risks.
12. Q. How to adjust the level of lighting? (This is for reference only; can not operate here)
A: First, align the front side of the wall will stop, a distance of about 10 meters, pay attention to is not on any deviation, the body must maintain the level, in order to as accurately as possible, you can draw with chalk marks, note that vehicles should be in a normal under the standard that no extra load of the load, the final commissioning: one: the lights turn on, and its projection on the wall of the aperture is adjusted basis. The center of the two lights, the distance to the vehicle front axle should be equidistant projection with its wall, or be adjusted according to the third step; the right to the ground from the center of the lamp should be equidistant to its projection on the wall, the left light This distance will have higher than its projection 10CM. Second, regulation in a straight line, move the left headlight to be absolutely direct, whereas the right headlight may be slightly to the right, because it can see very clearly the right, foggy weather is particularly effective. Third, a headlight cover for easy adjustment, one with a thick cloth covered headlights, headlight so you can shoot a beam on the wall changes to the effective regulation, testing time by two screwdrivers, a adjust the height of the beam, the other to be used to adjust the width of the beam.
13. Q must be installed HID lights installed line group? What are the benefits of installing cable group?
Answer: not necessarily have to install all the cars line group, if the original car's power cord thick enough to not install line group; the other hand we must install line group. Line group and the double double-loop circuit of electrical safety devices protect the car circuit, the connection terminals to prevent corrosion of poor contact occurs, high current capacity wires connecting wires can be guaranteed not to blow, to reassure customers to use.
14. Q H4 (high / low) lights and other lights installed models any different?
A: Because the car using only one lamp H4 headlight lamps. Is the distance and the original halogen light as one type. So their is a three-wire power input (ie, sharing a positive, two negative separately.) And my company is a H4 HID lamp, put in a HID lamp, an ordinary halogen lamps, so the installation should pay attention to ordinary halogen. Ordinary halogen or 12V DC power supply, and HID lamps must be connected HID lamp ballast power lines to complete the final. Be sure to install the lamp power control line distance to distinguish, but can not be an ordinary halogen lamp HID lamp connected with the same input power supply.
http://www.wphidled.com/
Sales Manager : Amy Feng
MSN : Amy@wplamps.com Email : Amy@wplamps.com
Alibaba: cn220020193 Phone: 0086-13126403867
|
|
|
|
|
|
|
|
|
|
